All Products | AA Express | Archive Appliance | G Enterprise | G Entry Level & Midrange
 
Home
FAQ
Submit a question
Favorites
Categories
AA24-AA32 (52)
AA80-AA174 (52)
AA638 A8/A12 (53)
AA Express (43)
Archive File Manager(AFM) (2)
AS400 & G-Series (7)
D-Series CD/DVD (9)
Diamond Software (30)
Enterprise AA (EAA) (3)
G Enterprise (15)
G Entry & Midrange (9)
LD6100-LD6600 (29)
LD8100-LD8600 (25)
M-Series (4)
Raidtec (100)
UDO Drives & Drivers (8)
Misc (3)
Misc. Information
AA80 - AA174 (ASP) (14)
AA24 - AA32 (ASP) (12)
AA Express (ASP) (8)
AA638 A8/A12 (ASP) (15)
D Series (ASP) (5)
Enterprise AA (ASP) (1)
G Enterprise (ASP) (17)
G Entry & Midrange (ASP) (18)
V-Series(ASP) (1)
Forms-Procedures (ASP) (2)
Kodak Service & Support Use
UDO Drives (ASP) (1)
UDO1 and UDO2 Drive Information
Search Articles
Advanced Search
Frequently Asked Questions
Search our FAQ to find resolutions to common issues.
Main Page
What is the shipping address for returning parts to ASTI in the United States?

All return shipments to ASTI U.S.A must include an RMA number or a contact name and number for the return shipment.

Improperly marked shipments will be returned to the sender.

The address for returning parts to the ASTI U.S.A site is:

Alliance Storage Technologies Inc.
Attn: Receiving/RMA# _________
9925 Federal Dr. Suite 100
Colorado Springs, CO 80921
719-593-4210

 
Article ID: 10358 Article Created: 11-13-2007 12:06 PMLast Modified: 06-21-2010 11:35 AM

Print  Email  Save  Notify Me  Add to Favorites 


Most Recently Viewed Articles
When I save the settings and go to the RAID status page in the web GUI,I get a message next to the RAID that says "Resync Delayed"
I have a RAID5 configured with all 4 drives on an S4-300 with no Hotspare. One of the drives failed and I replaced it according to the instructions in the user manual. I formatted the new drive and set it to hotspare. I also set the RAID properties to use a hotspare. When I save the settings and go to the RAID status page in the web GUI,I get a message next to the RAID that says "Resync Delayed". I have tried rebooting the Snaz but I get the same thing. What is the cause of this and how do I get the Resync to start?...
Where can spare / replacement part numbers and part costs be found?
All spare parts are found in the Customer Care Guide...
What are the configurations and status of the AAs installed in the support area?
The support area has several AAs that provide access to different software levels, configurations and products....
Why can't I connect to TextRAIDman via HyperTerminal?
Why can't I connect to TextRAIDman via HyperTerminal?...
How big is the read ahead buffer in the LD8000?
How big is the read ahead buffer in the LD8000?...
How do I increase the baud rate on serial port of the Infortrend Controller?
How do I increase the baud rate on serial port of the Infortrend Controller?...
Can I use the SNMP (Simple Network Management Protocol) to monitor the unit remotely?
Can I use the SNMP (Simple Network Management Protocol) to monitor the unit remotely? (i.e. send pager alerts when alarms signal my attention). If so does this equipment have a specific MIB file (Management Information Block)  for component monitoring?...
How often should the LM6000 media be cleaned?
How often should the LM6000 media be cleaned?...
Why does Raidtec Manager V2.2 exit when I try to create a RAID?
Why does Raidtec Manager V2.2 exit when I try to create a RAID?...
"FibreArray 2002" is displayed in the LCD. It means?
The EAM on my 2xxx is not coming online.  It displays "FibreArray 2002" on the LCD. What could be wrong?...